Ice maker hookup, how to install a water line for a refrigerator

Ice maker hookup

How to Install a Water Line for a Refrigerator Ice Maker

She attended Tarrant County College and studied English composition. Watch for leaks at all the connections. Thread the ferrule from the kit onto the new line.

  • Disconnect the Existing Water Line.
  • Leave the excess water line behind the refrigerator.
  • Measure the distance carefully, and buy a supply tube with plenty of length for the job.
  1. The valve connected to the right side of the faucet is the cold water supply line.
  2. Usually, this will be at some other existing water hookup point, like the water supply lines connected to your sink faucet or dishwasher.
  3. You will also need a longer flex water supply tube to run from the water pipe to the refrigerator.
  4. If there is no water dispenser, throw away the first full batch or two of ice to make sure it is all clean and ready to use.
Ice maker hookup

You can solve this with an ice maker installation kit that allows you to use the plumbing beneath the sink. Thread the water line, included in the ice maker installation kit, from the area behind the refrigerator to beneath the sink. Running a water line to a refrigerator to supply its ice maker and drinking water dispenser has never been easier. If running the line through the cabinets is not feasible, you might need to run a line through the floor and up to where the refrigerator is located. Wrap the female thread on the opposite end of the adapter with thread-seal tape.

How to Hook Up a Water Line to a Refrigerator From the Sink

How to Install a Water Line for a Refrigerator

Flex water supply tubes are available in either a tough plastic nylon mesh or braided steel. Use pliers to untwist the faucet supply line from the cold water supply valve. Coil the excess water line behind the refrigerator.

Adapt-a-Tees can be used in many situations where you need an extra line. Turn the water supply valve on and check for leaks. Now turn on the faucet shutoff valve under the sink and check for leaks at the Adapt-a-Tee connections. Although the braided steel is considerably more expensive, the extra strength it provides is well worth the investment. Twist the male end of a quick-tee adapter onto the valve.

First, locate the shutoff valve under the kitchen sink where you want to connect the new water line. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Turn the cold water supply valve on beneath the sink.

Ice maker hookup

How to Install a Water Line for a Refrigerator

HowStuffWorks

She writes mainly home improvement, health and travel articles for various online publications. Do not twist the nuts too tight as this could damage the supply valve, the supply line and the adapter. In most cases, the water line can be run from a kitchen faucet water supply line through the kitchen cabinets and over to the refrigerator. Turn on the cold water faucet to drain any water left in the supply line. If so, your job is very easy.

How to Install a Water Line for a Refrigerator

Drill holes in the base cabinet walls to route the water line from beneath the sink to the rear of the refrigerator. Insert the new water line into the opening on the tee. Shut off the water at the valve that controls the cold-water supply pipe to the faucet. Twist the faucet supply line onto the female end of the adapter. Tighten the fittings as needed, mayhem using channel-type pliers or an adjustable wrench.

The kit provides you with the required parts to hook up a water line to your refrigerator. Push the refrigerator against the wall. Turn the cold water on the supply line clockwise to close it. They come in various sizes to suit whatever situation you have.

How to Install a Water Line for a Refrigerator Ice Maker

Slip the remaining compression nut and ferrule over the refrigerator end of the new water line.

Tapping the Cold Water Line

If there are no fixure shutoff valves, you can turn off the water by closing the main water supply valve to the entire house. Tighten the connections slightly if you see a leak. Also, check for leaks where the supply tube connects to the refrigerator before pushing the appliance back into place.

How to Hook Up a Water Line to a Refrigerator

The tee adapter connects to the water supply shutoff valve. Connect the Supply Tube to the Refrigerator. Run the new supply tube to the back of the refrigerator.

Ice maker hookup
How to Hook Up a Water Line to a Refrigerator From the Sink

Slip the compression nut that came with the kit over the newly installed supply line. Find your water supply lines beneath your sink. If the refrigerator has a water dispenser, website flush out several gallons to purge the line of all the air.

Home Guides

Turn the supply line on once again. Plug your refrigerator into the wall. Tighten the connection just slightly more than hand-tight, shoes using pliers.

If you don't have a convenient water supply pipe and valve near the refrigerator, you must instead find another spot to hook up the water line. Drill as close to the back wall of the cabinet as possible, so you do not lose storage space inside the cabinet. Disconnect the faucet supply tube from the shutoff valve. Adapt-A-Tees are easy to install, first base second and they provide the extra line you need with the least amount of work. Tighten all three nuts on the quick-tee adapter with pliers or an adjustable wrench.

How to Hook Up a Water Line to a Refrigerator

An Adapt-a-Tee is an ideal plumbing fitting for this purpose. Connect the line to the water line connector on the back of the refrigerator. Attach the Adapt-a-Tee adapter to the shutoff valve, tightening by hand at first.

  • Speed dating in lancaster uk
  • Best american dating app
  • Boyfriend keeps joining dating sites
  • Dating johnnie walker bottles
  • Dating a jewish woman
  • Dating places in manila
  • Dating a complete gentleman