Here are the colours and the channels. Now for the Remote blue wire. Make sure this wire is safe from any moving objects.
Just for anyone who might be interested, here are my system specs. Or if you can't find one then you could always connect a single speaker and use the balance and fade options on the unit to work it out for yourself. Always be careful with electricity.
- Then tape it in with masking tape or some other tape that will hold it in.
- See the attached picture for an example of the correct connector.
- If yours is buried under the carpet or run nicely under your back seat because your amp is far from your sub, don't rip it out.
Things You'll Need Stereo. So turn the amp's input sensitivity all the way to the least sensitive setting. If you're bridging two channels, make sure they're bridged the same way. Subwoofer connection to a two-channel system differs from the methods used in home theaters. Lightly sand the contact area to expose clean metal before attaching ground.
Be respectful, keep it civil and stay on topic. Another power supply note, if this is going to be permanent then I highly suggest you follow one of the numerous test bench power supply mods on this site. Warnings Make sure that the power wires don't touch the terminal next to them on the amp or you'll create a massive short that can spark and start fires. Will the wires still match up on the aftermarket radio I purchased?
Find one of the lines with four pin, white molex connectors and then find the last connector on the chain. This setup certainly has a kick to it, great for parties. Another power supply note, screw it they're all power supply notes. Include your email address to get a message when this question is answered. Tips If your amp doesn't turn on, check the amp fuses.
- After that simple setup your amp will now turn on as soon as you plug the power supply in and switch it on.
- Did you make this project?
- If you're using an after market head unit, go to an electronics store's stereo department and ask for a wiring harness from your car to the after market head unit.
- Clipping is the number one reason of bass distortion.
Cut all four wires with a scissors just before the white connector so it's just four bare wires. See the attached image for an example. Or if you have wire cutters, cut it into a shorter U shape.
When connecting a line out connector to a factory head unit, it is advisable to use both sets of speaker wires to maintain the left and right stereo effect from modern music. Electrical tape at the entry point will give the wire added protection. Either way, japan hook up culture as long as it sounds good and you can be sure nothing is overheating when your blasting your music you should be just fine. Fold out the paperclip so it's like one big arc like a narrow C shape. Let's say it's a Watt amp.
The remote antenna power wire is responsible for the antenna coming out of a car with a retractable antenna. Make sure you always turn off your amp when you leave your car, it will overheat and drain your battery. It will just plug into your truck and then connect color coordinated wires. How to choose between Switch Lite and New Switch.
It Still Works
Subs and amps should be matched as closely as possible for best performance and longevity. Then try playing a song with some bass and you should hear it coming out the sub. Then cover the end of the shorter black wire with electrical tape also.
Wiring a Car Audio Amplifier and Headunit Up Indoors Using PC Power Supply
That means you have to double up the connections on the receiver or amplifier see photo below that illustrates that connection method. What would be the best way to get audio from the three? The fuse amperage should match the gauge size. Is this article up to date? You want to ground your cap.
My amp is already installed and I just bought a new sub. Turn the gain all the way down, start playing music and turn it up to where you usually listen, dating simulation games for where the mids sound good. The speakers themselves are pretty irrelevant as it's the amp that's taking the power. This will be outdoor for my patio and does not need to be obsurd! As the picture shows you need to connect your ground on your amp to the black ground cable from the connector.
But will this watt psu be able to power the amp and sub? If you need to drill a hole in the fire wall, be careful not to hit anything on the other side and be sure the drilled hole will not cut through your power line. Once you have your two cables connected you're ready for your next step. Cookies make wikiHow better. Warnings Always Disconnect the Negative terminal from your battery before doing anything with electricity on your car.
Have your power wire taunt and find out where your cap. Get your capacitor as close to the amp as possible, dating jasper and use the same ground as you did for the amp. You should be able to connect it to the auxiliary on the back of the stereo unit. Run the power wire to your amp. If this doesn't happen then something's gone wrong.
Subwoofer and amp hook up in house
If you're running two subs from one amp, hook each up separately. The subwoofer is hooked up to the receiver with a single interconnect cable. Have you taken your subwoofer out for the winter or just have a spare one and want to hook it up to your computer or home theater? Gather your equipment Amp, Subs, Stereo, and wiring.
Any help is good help and I'll share the project. You want an amp more powerful than your sub, because you don't want your sub to clip. Now stick one end in the main power connector's green wire hole and stick the other end into any black wire's hole. Items you will need computer power supply subwoofer in box speaker wire paperclip wire stripper screwdriver electrical tape scissors. For more information read this post on how to set up a subwoofer.
How to Hook Up a Car Amp Inside the House to a Wall Outlet
Hook it to a fuse connected to ignition turn on, like your accessory power fuse. See the attached picture if you don't know what the adapter looks like. Subs can provide a foundation to the sound that few speakers can muster on their own. Stereo receivers, pre-amps, and integrated amplifiers rarely have subwoofer output jacks or offer bass-management options. If you've been lucky enough to get it working then post pics, links and whatever else to show your handy work off.
Hook up amp and subs in house
This step its pretty simple. Just go to any car audio shop and buy some speaker cable. See the next step for those details.
Get the Gadget Hacks Daily
Plug the power supply into the wall and switch it on. The sub cuts on and off at high volume when I use the auxiliary cord to phone. Did I need to put fuse between the first and second battery?
If your amp didn't come with a knob for that, it's a really crappy amp but there's still hope. Wrap electrical tape around the end of the red wire and do not strip it. The wires are not grounded properly, check to make sure the surface is clean, unpainted metal. Don't be an idiot, palaeontological dating definition turn your power supply unit off and disconnect it from the mains when you're working with the cables.